Justinhb
Newbie
Offline
Posts: 5
|
|
« on: April 21, 2014, 08:10:52 PM » |
|
If calmini doesnt offer a SYE then where does still ? I didnt see one here.. anyone point me in the right direction
|
|
|
Logged
|
|
|
|
conor1123
Full Member
Offline
Posts: 21
|
|
« Reply #1 on: April 21, 2014, 09:08:00 PM » |
|
For which vehicle? Here's the pathfinder one. http://www.calmini.com/detail.php?b=1&m=3&t=3&p=1161&n=All of the SYEs seem to have the same part number on Calmini so i'm guessing they are all the same.
|
|
|
Logged
|
1993 Pathfinder 4x4 3" lift ~ 3" BL ~ 33's Ready for SAS
|
|
|
SteeevO
Rugged Rocks Founder
Administrator
Hero Member
Offline
Posts: 3561
I'll tell you a story!
|
|
« Reply #2 on: April 23, 2014, 05:05:31 AM » |
|
I don't believe Calmini makes these anymore. As far as I know they still advertise them however they don't have them.
I can make one for you but I need slip yokes as cores. If you can send one in I can make a sye with both 1310 and 1350 bolt patterns in it. Feel free to give me a call to order.
Sent from my Desire HD using Tapatalk
|
|
|
Logged
|
Rugged Rocks Newsletter | Check out my articles on CrawlerNews.com!------------------------------------------ "When you hit the tree between the headlights thats understeer. Oversteer is when you hit the tree between the Tail Lights"
|
|
|
conor1123
Full Member
Offline
Posts: 21
|
|
« Reply #3 on: April 23, 2014, 09:46:43 AM » |
|
Ah, my bad! I keep forgetting that Calmini isn't removing this stuff off their site!
|
|
|
Logged
|
1993 Pathfinder 4x4 3" lift ~ 3" BL ~ 33's Ready for SAS
|
|
|
Justinhb
Newbie
Offline
Posts: 5
|
|
« Reply #4 on: September 23, 2014, 03:56:13 AM » |
|
if I send you a yoke from a 2 peice driveshaft will that work..? from my stock driveshaft...what ya think the turn around is on that and cost? message me if ya like or hell even text me 7176239234 ive finally got the hardbody out again... so its time to continue the build I had started.. also interested a a driveshaft
|
|
|
Logged
|
|
|
|
SteeevO
Rugged Rocks Founder
Administrator
Hero Member
Offline
Posts: 3561
I'll tell you a story!
|
|
« Reply #5 on: September 23, 2014, 09:32:59 PM » |
|
Justin, If you need a 1310 CV Rear Driveshaft, it will be about $374.95. if you don't need a cv then the price will drop pretty good. The SYE Yoke/Flange with 1310&1350 patterns in it is $149.95 Shipping will vary depending on where we are sending it to.
Feel free to give me a call during the week as well 909-547-4651
|
|
|
Logged
|
Rugged Rocks Newsletter | Check out my articles on CrawlerNews.com!------------------------------------------ "When you hit the tree between the headlights thats understeer. Oversteer is when you hit the tree between the Tail Lights"
|
|
|
ehtrain
Full Member
Offline
Posts: 15
|
|
« Reply #6 on: October 01, 2014, 06:44:03 PM » |
|
is it possible to just by the slip joint anywhere? You could make what ever you wanted with that possibly?
|
|
|
Logged
|
|
|
|
Justinhb
Newbie
Offline
Posts: 5
|
|
« Reply #7 on: February 10, 2015, 07:51:59 PM » |
|
so whats everyone do when it get to the point a SYE is needed? is one offered here? any pics? does any other spline count drive shaft fit that they make a SYE for.. whats the splince count on a jeep tcase?
|
|
|
Logged
|
|
|
|
SteeevO
Rugged Rocks Founder
Administrator
Hero Member
Offline
Posts: 3561
I'll tell you a story!
|
|
« Reply #8 on: February 11, 2015, 05:58:21 PM » |
|
you can either retube the driveshaft to accomodate the length or if you have a spare OEM slip yoke I can make a SYE
|
|
|
Logged
|
Rugged Rocks Newsletter | Check out my articles on CrawlerNews.com!------------------------------------------ "When you hit the tree between the headlights thats understeer. Oversteer is when you hit the tree between the Tail Lights"
|
|
|
Nissan Off Road & 4x4 Forum
|
|
|
|
Logged
|
|
|
|
|